Ricoh VT1730 Instruções de Operação Página 1

PRIPORT VT1730Operating Instructions

Supplying Ink1, Open the ink cover.r=2. Press down the release lever (greentab [A]). The ink pack holder slides outpart way.3. Pull out the ink pack h

5. Install a ink pack as shown in thefigure.5. Slide in the ink pack holder.6.Press thesetting lever (green tab [B])until it clicks.IJ If the setting

Suppiyl“ngTape For The Tape Dispenser (O@ion)SUPPLYING THE MASTER ROLL, INK, AND TAPESupplying Tape For The Tape Dispenser(Option)~ Make sure that the

SUPPLYING THE MASTER ROLL, INK, AND TAPESupplying Tape For The Tape D~penser (Option)5. Press the manual cut button to trim offthe leading edge of the

Cautions For Printing PaperOPERATIONOPERATIONCautions For Printing PaperOnly use printing paper that meets the following specifications:Size: Max.: 21

OPERATIONCautions When Using The Document FeederCautions When Using The Document FeederOnly use originals that meetthe following specifications:Size:M

Preparation For PrintingOPERATIONPreparation For PrintingClWhen you load thick and small paper, see page 16.Loading paper1.Open the paper feed table c

OPERATIONPreparation For Printing4. Place the paper on the paper feedtable.~Make sure every sheet in the stack is setevenly. This helps prevent papers

Preparation For PrintingOPERATIONSetting up the paper delivery table1.Open the paper delivery table.2.Move the paper delivery end plate tomatch the pr

OPERATIONPreparation For Printhq4.Adjust the paper delivery rollers tomatch the paper size,D Ifyoupositionthepaperdeliveryrollersonthe print area, eac

- Machine ExteriorMAJOR COMPONENTSMAJOR COMPONENTSMachine ExteriorTOP COVERADF UNITOpen this cover toThe Automatic Documentaccess the inside ofFeeder

Standard PrintingOPERATIONStandard PrintingClThe leading edge margin of the paper must be more than 5 mm, 1/5”, because if thereis no margm on the pap

OPERATIONStandard PrintinqWhen you use larger than A4 or81/2” x 11” size paper, set the originaltray extender.I4. Press the Master Making key.~The ori

Standard PrintingOPERATION7.Remove the prints from the paperdelivery table.D If a large number of sheets is stacked inthe paper delivery table (approx

OPERATIONRestoringThe Paper Feed And Paper Delivery TablesRestoring The Paper Feed And PaperDelivery Tables1.Turn off the main switch.2.Press down the

5.Move the paper delivery end plate toits original position.6. Return the paper delivery table and theoriginal tray extender (if necessary) totheir or

OPERATIONAdjustingThe Image PositionAdjusting The Image PositionIf the image position is not correct, adjust it before you start printing. Use the Ima

AdjustingThe Image PositionOPERATIONShifting the image to the right or left1. Press down the feed roller pressurelever.IJ If you do not press down the

OPERATIONAdjustingThe Image Position4. Adjust the paper delivery rollers to theprint paper position.Caution: Do not touch the paper deliveryrollers wh

AdjustingThe Image DensityOPERATIONAdjusting The Image DensityBefore you make a master:Use thepressingImage Density key beforethe Master Making key.Li

Changing The Printing SpeedUse the Speed key to adjust the rotation speed of the machine in accordance with theimage density and printing paper.Press

MAJOR COMPONENTSOperation PanelOperation Panel= Keys -IMAGE MODE KEYSPEED KEYPress to select the LinePress to adjust the rotationmode or Photo mode in

To Stop The Machine During A Printing RunOPERATIONTo Stop The Machine During A Printing RunIfyou wantto stop the machine during a print run and print

OPERATIONMaking Master And Prints AutomaticallyMaking Master And Prints AutomaticallyUse the Auto Cycle key to automatically process masters and make

Group Printing From The Same Original (Class Mode)OPERATIONGroup Printing From The Same Original(Class Mode)Use the Memory/Class key to make sets of p

OPERATIONGroup Printing From The Same Original (Class Mode)5.With the Number keys, enter the desired number of sets.Cl The maximum number of sets that

Group PrintingFrom Different Originals (Memory Mode)OPERATIONGroup Printing From Different Originals(Memory Mode)Use the Memory/Class key to make sets

OPERATIONGroup Printing From Different Originals (Memory Mode)6,7.8.9.Press the Enter key again. The memory returns to Memory 1.0If you store the numb

Photo Mode PrintingOPERATIONPhoto Mode PrintingWhen printing a photograph or a color original, select the Photo mode.D Moire patterns may occur when s

DAILY MAINTENANCEThermal HeadDAILY MAINTENANCEThermal HeadClean the thermal head after every second master roll. Otherwise, white lines mayappearCauti

Thermal HeadDAILY MAINTENANCE4.While pushing out the platen rollerrelease levers (located on both sidesof the feed roller),grip both ends of thefeed r

DAILY MAINTENANCEContact GlassContact GlassIfyou don’t clean the contactglass, black lines1.Open the ADF cover.may appear on prints.2.Wipe off the mnt

Operation PanelMAJOR COMPONENTSMEMORY/CLASS KEYPress to select groupprinting. See page 31and 33. \\NUMBER KEYSPress to enter thenumb~r of prints.STOP

Paper Feed Roller DAILY MAINTENANCEPaper Feed RollerIfyou don’t clean the paperfeed roller,the leading edge of the print may become dirty.1.Open the p

DAILY MAINTENANCEPaper Delivery RollersPaperIfyou don’tDelivery Rollersclean the paper delivery rollers, black lines may appear on the prints.1. Open

Exit SensorDAILY MAINTENANCEExit SensorIf you don’t clean the exit sensor, misfeeds may1.Open the paper delivery table.occur in the paper exitsection.

Drum ClamperIf you don’t clean the drum clamper, the master will not be set correctly around thedrum and the image position may not be consistent duri

TROUBLESHOOTiNGTROUBLESHOOTINGIf a malfunction or a misfeed occurs within the machine, the following indicators will blink orlight.MonitorsWhen the Mi

TROUBLESHOOTINGWhen the Open Cover/Unit Indicator (~) LightsMONITORIWHAT YOU SHOULD DOIPAGEClose the cover.I)D*Close the paper delivery fence.Set the

When The Misfeed Indicator LightsTROUBLESHOOTINGWhen The Misfeed Indicator (:+) Lights“ :++ A “ Original1.Open the ADF rover.2.Pull out the original g

TROUBLESHOOTINGWhen The Misfeed Indicator Lights“ :++ B “Paper misfeed in paper feed section1.Push down the feed roller pressurelever.2. Remove the mi

When The Misfeed Indicator LightsTROUBLESHOOTING— To prevent paper misfeeds:~ Curled paper.Correct the curl.IJ Wrinkled or wavy paper.Do not use such

TROUBLESHOOTINGWhen The Misfeed Indicator Lights“ :++ c “ MaStermisfeed in master feed sectionWarning: Be careful not to cut yourself on any sharp edg

INSTALLATION REQUIREMENTS Machine Environment Environments To AvoidINSTALLATION REQUIREMENTSMachine EnvironmentThe installation location should be car

When The Misfeed Indicator LightsTROUBLESHOOTINGII :++ E “ Paper wrapping around the drumWarning:Be careful not to cut yourself on any shatp edges whe

TROUBLESHOOTINGWhen The Misfeed Indicator Liahts— To prevent paper misfeed:D If there is a large solid fill image on the leading edge of original, set

When The Misfeed Indicator LightsTROUBLESHOOTING“:++Ft’Master misfeed in the master eject section. Masterwrapped around the drum.Warning:Be careful no

TROUBLESHOOTINGWhen The Misfeed Indicator LightsWhen a master misfeed occurs on the drum.1.Open the top cover.2.As shown in the illustration, open the

When The Misfeed Indicator LightsTROUBLESHOOTING“:% + G “ Paper misfeed in the paper exit section1.Remove the misfedpaper.~ Open the topcoveror paper

TROUBLESHOOTINGWhen The Open Cover/Unit Indicator LightsWhen The Open Cover/UnitLightsMake sure that the following covers and units areIndicator (~)cl

When The Supply/Exchange Indicators LightTROUBLESHOOTINGWhen The Supply/Exchange Indicators Lightfi Load paper.~ Load new ink cartridge.&Load new

TROUBLESHOOTINGWhen Other Indicators LightWhen Other Indicators LightM–The master is not wrapped around the drum.1,2.3.Open the top cover.Make sure th

Poor PrintingTROUBLESHOOTINGPoor PrintingDirtybackgroundIf the background of prints are dirty, thepress roller inside the machine is dirty.Make extra

OPERATION NOTES.OPERATION NOTESCl Make sure to make a few trial prints to check the image position because the image positionof the trial print may no

Power Connation Access To The MachineINSTALLATION REQUIREMENTSPower Connection0 Securely connect the power cord to a dedimted 120V,60HZ power source w

CAUTIONSCAUTIONSOperating Cautions1. While Printing:-Do not turn off the main switch.-Do not unplug the power cord.-Do not open the cover.-Do not move

CAUTIONS6. Do not operate the machine with any rovers off.7.Be careful not to cut yourself on any sharp edges when you reach inside the machineto remo

SPECIFICATIONSConfiguration:Printing”Process:Original Type:Original Weight:Image Mode:Original Size:Paper Size:Paper Weight:Printing Area:Print Speed:

SPECIFICATIONSWeight:51kg, l121bPowerPowerSource:120V 60Hz moreConsumption:Master Making:Dimensions:Printing:than 2.4Aless than 0.16 kWless than 0.16

SUPPLYING THE MASTER ROLL, INK, AND TAPESupplying The Master Roll.SUPPLYING THE MASTER ROLL, INK,AND TAPESupplying The Master RollCaution:Caution:When

4.Lift the pressure release Ieverin thedirection of the arrow to release thefeed roller pressure.5.Insert the leading edge of the masterroll under the

SUPPLYING THE MASTER ROLL, INK, AND TAPESupplying The Master Roll9.Remove the cut-off portion of themaster roll.~ Removethe cut-offmasterpapercomplete