Ricoh IS760D Guia de Instalação descarregar pdf (Página 101)

G829-8600

Quick Installation Guide

Network Scanning Unit Type A

Please read the Safety Information in the Operating Instructions before using this machine. It contains important information related to

USER SAFETY and PREVENTING MACHINE PROBLEMS.

Unpacking the Machine and Checking the

Contents of the Box

Check the contents of the box according to the follow-

ing list. If any items are missing, please contact your

sales or service representative.

Quick Installation Guide(this sheet)

CD-ROM

Power Cord

Where to Put the Machine

The Machine's location should be carefully chosen because

environmental conditions greatly affect its performance.

WARNING

• Confirm that the wall outlet is near the machine and freely acces-

sible, so that in event of an emergency, it can be unplugged easily.

• Only connect the machine to the power source described on this sheet.

• Avoid multi-wiring.

• Do not damage, break or make any modifications to the power cord.

Do not place heavy object on it, pull it hard or bend it more than

necessary. These actions could cause an electric shock or fire.

CAUTION

• Keep the machine away from humidity and dust. A Fire or an electric

shock might occur.

• Place the machine on a strong and level surface. Otherwise, the

machine might fall and cause personal injury.

• If you use the machine in a confined space, confirm that there is a

continuous flow of air.

Optimum Environment Conditions

Recommended temperature and humidity

89.6 F

54%

80.6 F 80%50 F80%

89.6 F 15%

50 F 15%

%RH

50 70 8060 90

59 F

70%

59 F

30%

77 F

30%

77 F

70%

32 C

54%

27 C 80%10 C 80%

32 C 15%

10 C 15%

%RH

10 20 30

15 C

70%

15 C

30%

25 C

30%

25 C

70%

Possible operation range Recommended range

The machine must be level within 5 mm,0.2" both front to rear

and left to right.

TDLH140E

Environments to Avoid

❒ Locations exposed to direct sunlight or strong light

❒ Dusty areas

❒ Areas with corrosive gases

❒ Areas excessively cold, hot, or humid

❒ Locations near an air conditioner or humidifier

❒ Locations near other electronic equipment

❒ Locations where the scanner might be subjected to frequent strong

vibration

Power Connection

Connect the power cord to a power source with the following specifications:

Product Specifications

North America

G829-17 power supply rating:

AC 120V, 60Hz

Europe/Asia

G829-27 power supply rating:

AC 220-240V, 50/60Hz

Electrical Outlet Requirements

North America

G829-17 Electrical Outlet Requirements:

AC 120V, 60Hz, min.2A

Europe/Asia

G829-27 Electrical Outlet Requirements:

AC 220-240V, 50/60Hz, min.2A

Connecting to a Scanner

via SCSI Cable

Connecting to a

Network

Connecting to a

Power Source

WARNING

• Do not use with a power source with a voltage different from the

specified voltage. Do not use a power outlet with multiple devices

plugged in. These could create the risk of fire or electric shock.

• Avoid the use of an extension cord.

• Do not damage, break, twist or modify the Power Cord. Placing heavy

objects on the cord, pulling on or bending it excessively can damage

the Power Cord, creating the risk of fire or electric shock.

• Never touch or unplug the power plug with wet hands. This can create

the risk of electric shock.

CAUTION

• When unplugging from an outlet, be sure to grasp the plug when

pulling. Never pull on the cord. This could damage the cord creating

the risk of fire or electrical shock.

Confirm that the power switch is set to off.

Connect the bundled AC adaptor and the power code.

Push the terminal of the AC adaptor all the way into the

power connector on this machine.

ZKJH070J

Note

❒ Be sure to use the power cord that comes with this machine.

Insert the power plug into the power outlet.

Turning on the Power

Turn on the power of this machine after turning on the power of the con-

nected scanner.

A Turn on the power of a scanner connected to this machine.

B Turn on the power of this machine.

Note

❒ You can turn off the powers of a scanner and this machine in any

order.

Before turning off the power

Before you turn off the power of this machine, make sure that a standby

screen is displayed on the display panel.

If you turn off the power while the Scanner Features menu is displayed,

all the settings that you have configured will be discarded, and this ma-

chine will return to its factory default status.

You should also confirm that the "

" is not displayed on the display panel

when you turn off the power. Otherwise, loss of a scanned data or failure

will occur in sending files.

Important

❒ Prepare a marketed SCSI cable before connection procedures.

Note

❒ This machine complies with the SCSI-2 standard. The SCSI inter-

face on this machine has a 50-pin half-pitch (pin type) connector.

Connect an ANSI-compliant shielded SCSI-2 cable to this machine.

Note that some combinations of cables and the devices may not

work together properly, so check this carefully.

❒ Only one scanner can be connected to this machine.

Assign a SCSI ID to one of the numbers from 0 to 6.

Note

❒ The SCSI ID of this machine is fixed to 7 and cannot be changed.

❒ Follow the instructions of the manual of your scanner to connect to

this machine for how to change the SCSI ID of your scanner.

Connect a SCSI cable to this machine.

ZKJH050J

Connect the other end of the SCSI cable to the SCSI

port of a scanner.

Important

❒ Use a 100BASE-TX (category 5) or10BASE-T network cable when

you connect this machine to a network.

Reference

See "Using Wireless LAN" in the Operating Instructions when using

an optional wireless LAN card

With the network cable you use for connection, create

a single loop about 15cm (6”)(

A) away from an end of

the cable, and then attach the ferrite core that comes

with this machine as illustrated below.

Note

❒ Skip this step when you use this machine in North America.

Insert the network cable’s end to the network interface

connector of this machine.

ZKJH060J

Insert the other end of the network cable to an appropriate

connector of a network device, such as an Ethernet hub.

AC Adaptor

Safety Instruction Sheet

Wireless LAN Card cover

Ferrite Core (Europe only)

Remove the plastic bag. Lift this machine and move it to

the place where you want to install it.

1 2 ... 96 97 98 99 100 101 102 103 104 105 106 ... 311 312

Comentários a estes Manuais

Sem comentários

Ricoh IS760D Guia de Instalação Página 101

Comentários a estes Manuais

Manuais e produtos relacionados com Digitalizar e Imprimir Ricoh IS760D